Communicate with Supplier? Supplier
Unity Shan Ms. Unity Shan
What can I do for you?
Chat Now Contact Supplier
 Tel:86-0592-5807279 Email:18059851632@answersplc.com
Home > Products > General Electric Fanuc > GE PLC 90-30 CPU Parts > IC693ALG222 Analog Voltage Input Module
IC693ALG222 Analog Voltage Input Module
  • IC693ALG222 Analog Voltage Input Module

IC693ALG222 Analog Voltage Input Module

    Payment Type: T/T
    Incoterm: FOB,CIF,EXW
    Min. Order: 1 Piece/Pieces
    Delivery Time: 1 Days

Basic Info

Model No.: IC693ALG222

28 Cm X 5 Cm X 28 Cm: 0.51 Kg

Additional Info

Packaging: CARTON PACKING

Transportation: Ocean,Land,Air

Port: XIAMEN

Product Description

IC693ALG222 Analog Voltage Input Module,GE PLC 90-30 CPU Parts,Rack Adaptor Bracket,Ge Automation Controls,Ge Input Simulator Module CPU PARTS Programmable PLC Communicate MODULES Robots DCS ,Analog Voltage Input - 16 Channel IC693ALG222 The 16-Channel Analog Voltage Input module provides up to 16 single-ended or eight differential input channels, each capable of converting an analog input signal to a digital value for use as required by your application. This module provides two input ranges: 0 to 10 V (unipolar) 10 to +10 V (bipolar) Voltage Ranges and Input Modes The default input mode and range is single-ended, unipolar, with the user data scaled so that 0 volts corresponds to a count of 0 and 10 volts corresponds to a count of +32000. The other range and mode are selected by changing the configuration parameters using the Logicmaster 90-30/20/Micro or CIMPLICITY Control configurator software, or the Hand-Held Programmer. The range can be configured for bipolar 10 to +10 V where 10 V corresponds to a count of 32000, 0 V corresponds to a count of 0, and +10 V corresponds to a count of +32000. High and Low alarm limits are available on all ranges. Ranges can be configured on a per channel basis. Power Requirements and LEDs This module consumes a maximum of 112 mA from the 5V bus on the PLC backplane. It also requires a maximum of 41 mA from the backplane Isolated+24 Volt DC supply to power the on-board power converter that provides isolated 5V supplies to power the user-side circuitry (see Table 3-9, Specifications). There are two green LED indicators on the module which provide module and user supply status. The top LED, MODULE OK provides module status information on power-up as follows: ON: status is OK, module configured OFF: no backplane power or software not running (watchdog timer timed out) Continuous rapid flashing: configuration data not received from CPU Slow flashes, then OFF: failed power-up diagnostics or encountered code execution error The bottom LED, Power Supply OK, indicates that the internally generated user-side +5V supply is above a minimum designated level. Location in System This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC system. References Used The number of 16-Channel Analog Voltage Input modules which may be installed in a system depends on the amount of %AI and %I references available. Each module uses 1 to 16 %AI references (depending on the number of channels enabled) and from 8 to 40 %I references (depending on alarm status configuration). The available %AI references are: 64 with CPUs 311, 313, and 323; 128 with CPU331; 1024 with CPUs 340 and 341; and 2048 with CPUs 350 364. 10 10-10 Series 90-30 PLC I/O Module Specifications July 2000 GFK-0898F The maximum number of 16-Channel Analog Voltage Input modules which may be installed in a system are: 4 in a system using CPUs 311, 313, or 323 8 in a system using CPU331 12 in a system using CPUs 340 or 341 51 in a system using CPUs 350 364 When planning the module configuration for your application you must also consider the load capacity of the installed power supply and the total load requirements of all modules that are installed in the baseplate. Refer to the Series 90-30 Programmable Controller Installation Manual, GFK-0356 for details on power supplies and module load requirements. Table 10-3. Specifications for 16-Channel Analog Voltage Input Module, IC693ALG222 Number of Channels 1 to 16 selectable, single-ended 1 to 8 selectable, differential Input Current Ranges 0V to +10V (unipolar) or 10V to +10V (bipolar); selectable each channel Calibration Factory calibrated to: 2.5 mV per count on 0V to +10V (unipolar) range 5 mV per count on 10 to +10V (bipolar) range Update Rate 6 msec (all 16 single-ended channels) 3 msec (all 8 differential channels) Resolution at 0V to +10V 2.5 mV (1 LSB = 2.5 mV) Resolution at 10V to +10V 5 mV (1 LSB = 5 mV) Absolute Accuracy 0.25% of full scale @ 25 C (77 F) 0.5% of full scale over specified operating temperature range Linearity < 1 LSB Isolation 1500 volts between field side and logic side Common Mode Voltage (Differential) 11V (bipolar range) Cross-Channel Rejection > 80 db from DC to 1 kHz Input Impedance >500K ohms (single-ended mode) >1M ohms (differential mode) Input Filter Response 41 Hz (single-ended mode) 82 Hz (differential mode) Internal Power Consumption 112 mA (maximum) from the backplane +5 VDC bus 41 mA (maximum) from the backplane Isolated +24 VDC supply Refer to Appendix B for product standards and general specifications. The summation of the differential input, common-mode voltage, and noise must not exceed 11 volts when referenced to COM. In the presence of severe RF interference (IEC 801-3, 10V/m), accuracy may be degraded to 5% FS. Analog Input Modules 10 GFK-0898F Chapter 10 Analog Input Modules 10-11 CPU Interface to the IC693ALG 222 Analog Voltage Input Module The Series 90-30 PLC uses the data within the %AI data table to record analog values for use by the programmable controller. This scheme for the 16-Channel Analog Voltage Input module is shown below. More information on the CPU interface to analog modules can be found at the beginning of this chapter. SERIES 90-30 CPU A/D CONVERTER DATA TABLE % AI USER CONNECTIONS ANALOG VOLTAGE INPUT MODULE CHx MICRO PROCESSOR BACKPLANE INTERFACE VLSI OPTO ISOLATION COM CHx (+) CHx+1 CHx ( ) 233K 233K 3300pf 3300pf + + 280K 280K a47042 NOTE: CHx AND CHx+1 INDICATE SINGLE-ENDED MODE; CHx (+) AND CHx ( ) INDICATE DIFFERENTIAL MODE Figure 10-9. 16-Channel Analog Voltage Input Module Block Diagram - IC693ALG222 Placement of A/D Bits within the Data Tables Since converters used in the analog modules are 12-bit converters, not all of the 16 bits in the data tables contain data required for the conversion. A version of the 12 bits is placed within the 16-bit data word corresponding to the analog point (in the %AI table). The Series 90-30 PLC system handles the integration differently for the various analog modules. The CPU does not manipulate the data from the input modules before placing it within the word in the %AI data table. The bits in the %AI data table which were not used in the conversion by the input module are either forced to 0 (zero) by the Analog Input Module. Placement of the 12 data bits from the A/D converter for an analog current input data word for the 16-Channel Analog Voltage Input module in unipolar range is shown below. X D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X MSB LSB X=not converted bits Analog values are scaled over the range of the converter. Factory calibration adjusts the analog value per bit (resolution) to a multiple of full scale (that is, 2.5 mV/bit for unipolar; 5 mV/bit for bipolar). This calibration leaves a normal 12-bit converter with 4000 counts (normally 212 = 4096 counts). The data is then scaled with the 4000 counts over the analog range. For example, the data to the A/D converter for the 16-Channel Analog Voltage Input is scaled as shown below. 10 10-12 Series 90-30 PLC I/O Module Specifications July 2000 GFK-0898F A/D BITS (decimal) VOLTAGE; 0 to 10V RANGE a45717 0 10 0 4000 Figure 10-10. A/D Bits vs. Voltage Input for IC693ALG222.


Product Details:

Description:


IC693ALG222 Analog Voltage Input Module




Model Number:

IC693ALG222


Manufacturer(s) :

GE

Product Type:

Analog Voltage Input Module

Warranty:

1 Year

Plance of Origin:

Made in USA

Estimated Shipping Size:

Dimensions: 1" x 5" x 5" (4 cm x 13 cm x 13 cm)

Weight: 0 lbs 13 oz (0.36 kg)

IC693ALG222



Advantage brands :

GE

IC693CPU363,IC697PWR711,IC693CPU364,IC693,IC697,IC695,IS200,IS215,DS200...


Allen Bradley


1756-L62,1756-L63,1746,1747,1756,1769,1794,2711P..


SCHNEIDER

140CPU43412U,140CPU65150,140CPU65160,140CPU,NOE,CRA,CPS,BMX,TCSE....


ABB

DSQC(07KT98 WT98,07KT97 WT97,DSQC679,IMASI23,IMDSO14...)


Bently Nevada

3500/42M,3500/22M,3500/95.3500/15...


TRICONEX

3805E,3008,3504E,3624,3700A,3721,4351B,4119A.. ..


Siemens Moore

6ES7(1.2.3.4),6ES5,6DD,6DP....


IC697CPM925

IC697CPU731

IC697CPU772

IC697CPU781

IC697CPU782

IC697CPX772

IC697CPX935

IC697CPX935-FD

IC697MDL240

IC697MDL250

IC697MDL350

IC697MDL653

IC697MDL740

IC697MEM715

IC693ALG442 As an Analog Current/Voltage Combination Input/Output the GE Fanuc 90-30 IC693ALG442 provides up to 4 differential input current or voltage channels and 2...
IC693APU300 High Speed Counter GE Fanuc 90-30 IC693APU300 is a single-slot module which can be used in applications where pulse input rates exceed the input capability of...
IC693APU301 The Motion Mate APM GE Fanuc 90-30 IC693APU301 is an easy-to-use intelligent, fully programmable 1-axis motion control module. The GE Fanuc 90-30 IC693APU301...
IC693APU302 The Motion Mate APM GE Fanuc 90-30 IC693APU302 is an easy-to-use intelligent, fully programmable 2-axis motion control module. The GE Fanuc 90-30 IC693APU302...
IC693APU305 An I/O Processo, the GE Fanuc 90-30 IC693APU305, provides direct processing of rapid pulse signals for industrial control applications. GE Fanuc 90-30...
IC693BEM320
The GE Fanuc 90-30 IC693BEM320 provides an interface between a Series 90-30 PLC and a proprietary Fanuc I/O LINK in a Fanuc CNC (Computer Numerical...

IC693BEM321 A GE Fanuc 90-30 IC693BEM321 is configured as a master module on a proprietary Fanuc I/O LINK. GE Fanuc 90-30 IC693BEM321 can receive 1024 discrete inputs...
IC693BEM331 The GE Fanuc 90-30 IC693BEM331 provides the interface between a Series 90-30 PLC and a Genius I/O serial bus. GE Fanuc 90-30 IC693BEM331 receives and...
IC693CBL300




Looking for ideal IC693ALG222 Input Module Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the GE Analog Voltage are quality guaranteed. We are China Origin Factory of 8 Differential Input Channels. If you have any question, please feel free to contact us.

Product Categories : General Electric Fanuc > GE PLC 90-30 CPU Parts

Email to this supplier
  • Ms. Unity Shan
  • Your message must be between 20-8000 characters

Related Products List

Home

Phone

Skype

Inquiry